|
Product introduction:
TIC-EOP2080 series Ethernet converter supports the transparent transmission of Ethernet data on 1~8 route E1 channel. The maximum bit rate is 15.84Mb/s .With different LAN card,E1 card and power card to meet .TIC-2080 provides alarms and statuses monitoring of the E1 line and Ethernet interface together with advanced management functions, of high integration, low power consumption, stable performance and easy operation.
TIC-EOP2080 series Ethernet converter adopted international standard protocol at all levels, which can also communicate with the similar product of other manufacturers.
Product picture:
TIC-EOP2080-TX/FX/FXT Front panel
TIC-EOP2080-TX/FX/FXT-M(SNMP) Front panel
TIC-EOP2080-TX-75 Back panel（AC220V）
TIC-EOP2080-TX-75 Back panel（DC-48V）
TIC-EOP2080-TX-75 Back panel（AC220V/DC-48V）
TIC-EOP2080-TX-120 Back panel（AC220V/DC-48V）
TIC-EOP2080-FX-75 Back panel（AC220V/DC-48V）
TIC-EOP2080-FX-120 Back panel（AC220V/DC-48V）
TIC-EOP2080-FXT-75 Back panel（AC220V/DC-48V）
TIC-EOP2080-FXT-120 Back panel（AC220V/DC-48V）
TIC-EOPK2080-TX/FX/FXT Front panel
TIC-EOPK2080-TX Back panel
TIC-EOPK2080-FX Back panel
TIC-EOPK2080-FXT Back panel
Product Feature：
1.Transmitting interface（WAN E1）
Realizing conversion from electrical ethernet data to 1～8 route E1 channel between 1 route optical path/4 route electrocircuit/1 route optical path+3 route electrocircuit.
Supports automatic removal and recovery of E1 channels. The E1 channels provide urgent alarm if the Bit Error Rate (BER) exceeds 1E-6, and during this period, some Ethernet packets may be lost; It will be resumed when the fault dismisses.
E1 The differential delay between any two of the 8 E1 can be up to 220ms; when the factual differential delay exceeds 220ms, alarm is generated and Ethernet is cut off
Jitter tolerance and jitter transfer characteristic are compliant to ITU-T G.823 standard.
Ethernet data will not be damaged when transmission bandwidth increases; non-injury Ethernet data can be achieved through network management system when artificially reduced transmission bandwidth.
E1 signal loop-back detection and automatic cut-off function; when certain E1 i detected to be loop-back,this E1 will be cut off ,and it will be recovered automatically after release of loop-back.
Support remote end/local E1 loop-back detection function.
2.Ethernet interface(LAN )
The maximum bandwidth is 15.84 Mbps.
Accord with the IEEE 802.3 protocol standard to support 100M full duplex, providing up to four shared Ethernet interface.
Provide 1024 MAC address lists, auto update time is 5 minutes.
Support the maximum long frames up to1916 bytes, and the minimum frames are 64 bytes.
Optional optical ethernet interface and electrical interface according with IEEE 802.3 standard（can be used together with Fiber Optical Transceiver ）.
Support VLAN function based on label,accord with IEEE 802.1Q standard.
Support PAUSE flow control function.
3.Timing mode
Optional local timing and E1 channel timing.
The source of tracing E1 line can be switched according to the signal quality. For instance, the system is set as tracing the first E1 link, when some malfunction occurs to it, the system will automatically change to tracing the second E1 link; when the fault disappear, the system will be re-tracing the first E1 link.
4.Compliant to ITU-T standards
GFP-F encapsulation accord with G.7041 standard.
VCAT virtual concatenation and LCAS link capacity regulation means accord with G.7042 standard.
Mapping from Ethernet to nxE1 accord with G.7043 standard.
Mapping from Ethernet to single E1 accord with G.8040 standard.
Equipment will delete E1 channels which have fault or high error rate automatically and resume when the fault disappear.
E1 branch of both ends can be connected without order to benefit the installation.
5.Device network management
CLI command line management based on serial port.
SNMP(V1 / V2C) XVIEW management software.
Typical application:
Technical Specification：
|
E1 interface |
|
Interface characteristics |
In accord with G.703﹑G.704﹑G.823 |
|
Interface velocity |
2048Mbps±50ppm |
|
Line code type |
HDB3 |
|
75Ω unbalanced |
DB37 |
|
120Ω balanced |
RJ45 |
|
Ethernet Interface |
|
Interface characteristics |
In accord with IEEE802.3，802.3u |
|
Connector |
10/100Base-T，Auto-MDI/MDIX |
|
Bandwidth |
15.84Mbps |
|
Optical ethernet interface（TIC-EOP(K)2080-FX/FXT) |
|
Interface characteristics |
In accord with IEEE 802.3u 100Base-Fx |
|
Interface type |
Single-mode/multi-mode;
Single fiber/ multi fiber FC/SC/ST/SFP |
|
Central wavelength |
850nm/1310nm/1550nm |
|
Optical output power |
>-9dBm |
|
Receiving sensitivity |
Single-mode：<-35dBm;
Multi-mode：<-20dBm (BER≤10-11) |
|
Transmission rate |
125Mb/s |
|
Transmission distance |
Single-mode：40KM、80KM、100KM;
Multi-mod：0～2km |
|
Electrical characteristics |
|
Power supply |
AC220V/DC-48V |
|
Voltage fluctuation range |
AC165~265V/DC-36~-72V |
|
Power consumption |
<15W |
|
Ambient characteristics |
|
Service temperature |
-5°C~+50°C |
|
Storage temperature |
-25°C~+55°C |
|
Working humidity |
10~90%, without condensation |
|
EMC |
|
In accord with GJB151A-97 and SC standard |
Ordering information:
|
No |
Model |
Description |
Outside dimensions |
|
1 |
TIC-EOP2080-TX-75-A |
4*electrical Ethernet,75Ω,AC |
440mm×44mm×230mm |
|
2 |
TIC-EOP2080-TX-75-D |
4*electrical Ethernet,75Ω,DC |
440mm×44mm×230mm |
|
3 |
TIC-EOP2080-TX-75-AD |
4*electrical Ethernet,75Ω,AC+DC |
440mm×44mm×230mm |
|
4 |
TIC-EOP2080-TX-75-M-A |
4*electrical Ethernet,75Ω,SNMP,AC |
440mm×44mm×230mm |
|
5 |
TIC-EOP2080-TX-75-M-D |
4*electrical Ethernet,75Ω,SNMP,DC |
440mm×44mm×230mm |
|
6 |
TIC-EOP2080-TX-75-M-AD |
4*electrical Ethernet,75Ω,SNMP,AC+DC |
440mm×44mm×230mm |
|
7 |
TIC-EOP2080-TX-120-A |
4*electrical Ethernet,120Ω,AC |
440mm×44mm×230mm |
|
8 |
TIC-EOP2080-TX-120-D |
4*electrical Ethernet,120Ω,DC |
440mm×44mm×230mm |
|
9 |
TIC-EOP2080-TX-120-AD |
4*electrical Ethernet,120Ω,AC+DC |
440mm×44mm×230mm |
|
10 |
TIC-EOP2080-TX-120-M-A |
4*electrical Ethernet,120Ω,SNMP,AC |
440mm×44mm×230mm |
|
11 |
TIC-EOP2080-TX-120-M-D |
4*electrical Ethernet,120Ω,SNMP,DC |
440mm×44mm×230mm |
|
12 |
TIC-EOP2080-TX-120-M-AD |
4*electrical Ethernet,120Ω,SNMP,AC+DC |
440mm×44mm×230mm |
|
13 |
TIC-EOP2080-FX-75-A |
1*optical Ethernet,75Ω,AC |
440mm×44mm×230mm |
|
14 |
TIC-EOP2080-FX-75-D |
1*optical Ethernet,75Ω,DC |
440mm×44mm×230mm |
|
15 |
TIC-EOP2080-FX-75-AD |
1*optical Ethernet,75Ω,AC+DC |
440mm×44mm×230mm |
|
16 |
TIC-EOP2080-FX-75-M-A |
1*optical Ethernet,75Ω,SNMP,AC |
440mm×44mm×230mm |
|
17 |
TIC-EOP2080-FX-75-M-D |
1*optical Ethernet,75Ω,SNMP,DC |
440mm×44mm×230mm |
|
18 |
TIC-EOP2080-FX-75-M-AD |
1*optical Ethernet,75Ω,SNMP,AC+DC |
440mm×44mm×230mm |
|
19 |
TIC-EOP2080-FX-120-A |
1*optical Ethernet,120Ω,AC |
440mm×44mm×230mm |
|
20 |
TIC-EOP2080-FX-120-D |
1*optical Ethernet,120Ω,DC |
440mm×44mm×230mm |
|
21 |
TIC-EOP2080-FX-120-AD |
1*optical Ethernet,120Ω,AC+DC |
440mm×44mm×230mm |
|
22 |
TIC-EOP2080-FX-120-M-A |
1*optical Ethernet,120Ω,SNMP,AC |
440mm×44mm×230mm |
|
23 |
TIC-EOP2080-FX-120-M-D |
1*optical Ethernet,120Ω,SNMP,DC |
440mm×44mm×230mm |
|
24 |
TIC-EOP2080-FX-120-M-AD |
1*optical Ethernet,120Ω,SNMP,AC+DC |
440mm×44mm×230mm |
|
25 |
TIC-EOP2080-FXT-75-A |
1*optical Ethernet,3*electrical Ethernet,75Ω,AC |
440mm×44mm×230mm |
|
26 |
TIC-EOP2080-FXT-75-D |
1*optical Ethernet,3*electrical Ethernet,75Ω,DC |
440mm×44mm×230mm |
|
27 |
TIC-EOP2080-FXT-75-AD |
1*optical Ethernet,3*electrical Ethernet,75Ω,AC+DC |
440mm×44mm×230mm |
|
28 |
TIC-EOP2080-FXT-75-M-A |
1*optical Ethernet,3*electrical Ethernet,75Ω,SNMP,AC |
440mm×44mm×230mm |
|
29 |
TIC-EOP2080-FXT-75-M-D |
1*optical Ethernet,3*electrical Ethernet,75Ω,SNMP,DC |
440mm×44mm×230mm |
|
30 |
TIC-EOP2080-FXT-75-M-AD |
1*optical Ethernet,3*electrical Ethernet,75Ω, SNMP,AC+DC |
440mm×44mm×230mm |
|
31 |
TIC-EOP2080-FXT-120-A |
1*optical Ethernet,3*electrical Ethernet,120Ω,AC |
440mm×44mm×230mm |
|
32 |
TIC-EOP2080-FXT-120-D |
1*optical Ethernet,3*electrical Ethernet,120Ω,DC |
440mm×44mm×230mm |
|
33 |
TIC-EOP2080-FXT-120-AD |
1*optical Ethernet,3*electrical Ethernet,120Ω,AC+DC |
440mm×44mm×230mm |
|
34 |
TIC-EOP2080-FXT-120-M-A |
1*optical Ethernet,3*electrical Ethernet,120Ω,SNMP,AC |
440mm×44mm×230mm |
|
35 |
TIC-EOP2080-FXT-120-M-D |
1*optical Ethernet,3*electrical Ethernet,120Ω,SNMP,DC |
440mm×44mm×230mm |
|
36 |
TIC-EOP2080-FXT-120-M-AD |
1*optical Ethernet, 3*electrical Ethernet,120Ω, SNMP,AC+DC |
440mm×44mm×230mm |
|
37 |
TIC-EOPK2080-TX-75 |
2*electrical Ethernet,75Ω（card） |
483mm×265mm×230mm（6U） |
|
38 |
TIC-EOPK2080-TX-75-M |
2*electrical Ethernet,75Ω,SNMP（card） |
483mm×265mm×230mm（6U） |
|
39 |
TIC-EOPK2080-TX-120 |
2*electrical Ethernet,120Ω（card） |
483mm×265mm×230mm（6U） |
|
40 |
TIC-EOPK2080-TX-120-M |
2*electrical Ethernet,120Ω,SNMP（card） |
483mm×265mm×230mm（6U） |
|
41 |
TIC-EOPK2080-FX-75 |
1*optical Ethernet, 75Ω（card） |
483mm×265mm×230mm（6U） |
|
42 |
TIC-EOPK2080-FX-75-M |
1*optical Ethernet, 75Ω,SNMP（card） |
483mm×265mm×230mm（6U） |
|
43 |
TIC-EOPK2080-FX-120 |
1*optical Ethernet, 120Ω（card） |
483mm×265mm×230mm（6U） |
|
44 |
TIC-EOPK2080-FX-120-M |
1*optical Ethernet, 120Ω,SNMP（card） |
483mm×265mm×230mm（6U） |
|
45 |
TIC-EOPK2080-FXT-75 |
1*optical Ethernet,2*electrical Ethernet,75Ω,（card） |
483mm×265mm×230mm（6U） |
|
46 |
TIC-EOPK2080-FXT-75-M |
1*optical Ethernet,2*electrical Ethernet,75Ω,SNMP（card） |
483mm×265mm×230mm（6U） |
|
47 |
TIC-EOPK2080-FXT-120 |
1*optical Ethernet,2*electrical Ethernet,120Ω,（card） |
483mm×265mm×230mm（6U） |
|
48 |
TIC-EOPK2080-FXT-120-M |
1*optical Ethernet,2*electrical Ethernet,120Ω,SNMP（card） |
483mm×265mm×230mm（6U） |
|
Note |
Card must be installed in FOR-6U use by FOR-6U power supply (AC/DC optional) power supply |
|
|
|
